是否有最大尺寸的 SD 卡？需要什么格式？

当我第一次启动 ESP32 网络界面时，我解锁了警报以将其置于空闲模式。我转到 SD 卡并点击刷新。

这会导致这些事件：

22:28:18.972 -> [MSG:Caution: Unlocked]
22:29:25.543 -> ERROR检测到任务 clientCheckTask 中的堆栈溢出。
22:29:25.543 -> abort() 在核心 1 上的 PC 0x40090bf0 上调用
22:29:25.543 ->
22:29:25.543 -> ELF 文件 SHA256：00000000000000000
22:29:25.543 ->
22:29:25.543 – > Backtrace: 0x4009095c:0x3ffd4230 0x40090bd9:0x3ffd4250 0x40090bf0:0x3ffd4270 0x400934d7:0x3ffd4290 0x400950a0:0x3ffd42b0 0x40095056:0xa5a5a5a5
22:29:25.543 ->
22:29:25.543 -> Rebooting…
22:29:25.543 -> ets Jun 8 2016 00:22:57
22:29:25.543 ->
22:29:25.543 -> rst:0xc (SW_CPU_RESET),boot:0x17 (SPI_FAST_FLASH_BOOT)
22:29:25.588 -> configsip: 0, SPIWP:0xee
22:29:25.588 -> clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
22:29:25.588 -> 模式：DIO，时钟 div:1
22:29:25.588 -> load:0x3fff0018,len:4
22:29:25.588 -> load:0x3fff001c,len:1216
22:29:25.588 -> ho 0 tail 12 room 4
22:29:25.588 -> load:0x40078000,len:10944
22:29:25.588 -> 加载：0x40080400，len:6388
22:29:25.588 -> 条目 0x400806b4
22:29:26.153 ->
22:29:26.153 -> [MSG:Grbl_ESP32 Ver 1.3a 日期 20210816]
22:29 :26.153 -> [MSG:Compiled with ESP32 SDK:v3.3.5-1-g85c43024c]
22:29:26.153 -> [MSG:Using machine:Root Controller 3 Axis XYYZ]
22:29:26.200 -> [MSG:Axis count 3]
22:29:26.200 -> [MSG:I2S Steps, Stream]
22:29:26.200 -> [MSG: 复位引脚 GPIO(13) 上的开关]
22:29:26.200 -> [MSG: 保持引脚 GPIO(36) 上的开关]
22:29:26.200 -> [MSG: 启动开关在 pin GPIO(39)]
22:29:26.200 -> [MSG:Macro Pin 0 GPIO(34)]
22:29:26.200 -> [MSG:User Digital Output:0 on Pin:I2SO(17)]
22: 29:26.200 -> [MSG:用户数字输出:1 引脚:I2SO(18)]
22:29:26.200 -> [MSG:用户数字输出:2 引脚:I2SO(19)]
22:29:26.200 – > [MSG:Init Motors]
22:29:26.200 -> [MSG:Using StepStick Mode]
22:29:26.200 -> [MSG:X Axis Standard Stepper Step:I2SO(5) Dir:I2SO(6) Disable:I2SO (7) 限制(0.000,600.000)]
22:29:26.247 -> [消息:Y 轴标准步进:I2SO(2) 方向:I2SO(3) 禁用:I2SO(4) 限制(0.000,600.000)]
22:29:26.247 -> [MSG:Y2 轴标准步进：I2SO(15) Dir:I2SO(0) Disable:I2SO(1) Limits(0.000,600.000)]
22:29:26.247 -> [MSG:Z轴标准步进器步进：I2SO(12) Dir:I2SO(13) Disable:I2SO(14) Limits(-600.000,0.000)]
22:29:26.247 -> [MSG:Initializing RS485 VFD spindle]
22:29:26.247 – > [MSG:VFD RS485 Tx:GPIO(17) Rx:GPIO(16) RTS:GPIO(4)]
22:29:26.388 ->
22:29:26.388 -> [MSG:Client Started]
22:29:26.388 -> [MSG:Connecting HENRY]
22:29:26.388 -> [MSG:Connecting.]
22:29:26.859 -> [MSG:Connecting..]
22:29:27.376 -> [MSG:Connecting…]
22:29:27.861 -> [MSG:Connecting….]
22:29:28.375 -> [MSG:Connecting.]
22:29:28.888 -> [MSG:Connecting..]
22:29:29.359 -> [MSG:Connecting…]
22:29:29.874 -> [MSG:Connecting….]
22:29:29.969 -> [MSG:Connected with 192.168.0.42]
22:29 :30.394 -> [MSG: 使用主机名启动 mDNS:http://grblesp.local/%5D
22:29:30.394 -> [MSG:SSDP Started]
22:29:30.394 -> [MSG:HTTP Started]
22:29 :30.394 -> [MSG:TELNET Started 23]
22:29:30.394 -> [MSG:I2SO(21) 引脚上的溢流冷却剂]
22:29:30.394 -> [MSG:I2SO(20) 引脚上的喷雾冷却剂]
22 ：29：30.394 -> [MSG：引脚 GPIO(2) 上的 X 轴限位开关]
22：29：30.394 -> [MSG：引脚 GPIO(26) 上的 Y 轴限位开关]
22：29：30.442 -> [MSG :Y2 引脚 GPIO(27) 上的轴限位开关]
22:29:30.442 -> [MSG:Z 轴引脚 GPIO(14) 上的限位开关]
22:29:30.442 -> [MSG:Probe on pin GPIO(33)]
22:29:30.442 ->
22:29:30.442 -> Grbl 1.3a [‘$’寻求帮助]
22:29:30.442 -> [ MSG:’$H’|’$X’解锁]
22:29:32.555 -> [MSG:Spindle RS485 Unresponsive 8]