问题：安装 v3.4.5 后无法挂载 SD 卡 #436

勒韦里

控制板

6包

董事会供应商的帮助

是的
不
不适用

机器描述

‘ESP-WROOM-32’（流体术语：“芯片是 ESP32-D0WDQ6（修订版 1）”，带有 4MB 闪存），在 6-Pack_CNC_Controller、24V 10A Aclorol 电源中，X 和 Y 由“DRV8825”控制（目前没有Z，以后可能是伺服系统），运行“FluidNC v3.4.5（wifi）”

配置文件

board: 6 Pack
name: 6 Pack StepStick XY
meta: 
stepping:
  engine: I2S_stream
  idle_ms: 250
  pulse_us: 4
  dir_delay_us: 1
  disable_delay_us: 0
  segments: 6

axes:
  shared_stepper_disable_pin: NO_PIN
  shared_stepper_reset_pin: NO_PIN
  x:
    steps_per_mm: 200.300
    max_rate_mm_per_min: 5000.000
    acceleration_mm_per_sec2: 50.000
    max_travel_mm: 1300.000
    soft_limits: true
    homing:
      cycle: 2
      allow_single_axis: true
      positive_direction: false
      mpos_mm: 0.000
      feed_mm_per_min: 100.000
      seek_mm_per_min: 2500.000
      settle_ms: 500
      seek_scaler: 1.100
      feed_scaler: 1.100

    motor0:
      limit_neg_pin: gpio.16:pu
      limit_pos_pin: NO_PIN
      limit_all_pin: NO_PIN
      hard_limits: false
      pulloff_mm: 2.000
      stepstick:
        step_pin: I2SO.2
        direction_pin: I2SO.1
        disable_pin: I2SO.0
        ms1_pin: NO_PIN
        ms2_pin: NO_PIN
        ms3_pin: I2SO.3
        reset_pin: NO_PIN

  y:
    steps_per_mm: 200.050
    max_rate_mm_per_min: 5000.000
    acceleration_mm_per_sec2: 50.000
    max_travel_mm: 800.000
    soft_limits: true
    homing:
      cycle: 1
      allow_single_axis: true
      positive_direction: false
      mpos_mm: 0.000
      feed_mm_per_min: 100.000
      seek_mm_per_min: 2500.000
      settle_ms: 500
      seek_scaler: 1.100
      feed_scaler: 1.100

    motor0:
      limit_neg_pin: gpio.26:pu
      limit_pos_pin: NO_PIN
      limit_all_pin: NO_PIN
      hard_limits: false
      pulloff_mm: 2.000
      stepstick:
        step_pin: I2SO.5
        direction_pin: I2SO.4
        disable_pin: I2SO.7
        ms1_pin: NO_PIN
        ms2_pin: NO_PIN
        ms3_pin: I2SO.6
        reset_pin: NO_PIN

    motor1:
      limit_neg_pin: gpio.27:pu
      limit_pos_pin: NO_PIN
      limit_all_pin: NO_PIN
      hard_limits: false
      pulloff_mm: 2.000
      stepstick:
        step_pin: I2SO.10
        direction_pin: I2SO.9
        disable_pin: I2SO.8
        ms1_pin: NO_PIN
        ms2_pin: NO_PIN
        ms3_pin: I2SO.11
        reset_pin: NO_PIN

  z:
    steps_per_mm: 100.000
    max_rate_mm_per_min: 5000.000
    acceleration_mm_per_sec2: 100.000
    max_travel_mm: 5.000
    soft_limits: false
    homing:
      cycle: 0
      allow_single_axis: true
      positive_direction: true
      mpos_mm: 0.000
      feed_mm_per_min: 50.000
      seek_mm_per_min: 200.000
      settle_ms: 250
      seek_scaler: 1.100
      feed_scaler: 1.100

    motor0:
      limit_neg_pin: NO_PIN
      limit_pos_pin: NO_PIN
      limit_all_pin: NO_PIN
      hard_limits: false
      pulloff_mm: 2.000
      rc_servo:
        output_pin: gpio.12
        pwm_hz: 50
        min_pulse_us: 1000
        max_pulse_us: 2000

kinematics:
  Cartesian:

i2so:
  bck_pin: gpio.22
  data_pin: gpio.21
  ws_pin: gpio.17

spi:
  miso_pin: gpio.19
  mosi_pin: gpio.23
  sck_pin: gpio.18

sdcard:
  cs_pin: gpio.5
  card_detect_pin: NO_PIN

control:
  safety_door_pin: NO_PIN
  reset_pin: NO_PIN
  feed_hold_pin: NO_PIN
  cycle_start_pin: NO_PIN
  macro0_pin: NO_PIN
  macro1_pin: NO_PIN
  macro2_pin: NO_PIN
  macro3_pin: NO_PIN

coolant:
  flood_pin: NO_PIN
  mist_pin: NO_PIN
  delay_ms: 0

probe:
  pin: NO_PIN
  check_mode_start: true

macros:
  startup_line0: 
  startup_line1: 
  macro0: 
  macro1: 
  macro2: 
  macro3: 

start:
  must_home: true
  deactivate_parking: false
  check_limits: false

user_outputs:
  analog0_pin: NO_PIN
  analog1_pin: NO_PIN
  analog2_pin: NO_PIN
  analog3_pin: NO_PIN
  analog0_hz: 5000
  analog1_hz: 5000
  analog2_hz: 5000
  analog3_hz: 5000
  digital0_pin: NO_PIN
  digital1_pin: NO_PIN
  digital2_pin: NO_PIN
  digital3_pin: NO_PIN

arc_tolerance_mm: 0.002
junction_deviation_mm: 0.010
verbose_errors: true
report_inches: false
enable_parking_override_control: false
use_line_numbers: false
planner_blocks: 16
NoSpindle:

启动消息

ets Jun  8 2016 00:22:57

rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:1
load:0x3fff0030,len:1184
load:0x40078000,len:12804
ho 0 tail 12 room 4
load:0x40080400,len:3032
entry 0x400805e4

[MSG:INFO: FluidNC v3.4.5]
[MSG:INFO: Compiled with ESP32 SDK:v4.4-beta1-189-ga79dc75f0a]
[MSG:INFO: Local filesystem type is SPIFFS]
[MSG:INFO: Configuration file:220519_1325.yaml]
[MSG:INFO: Machine 6 Pack StepStick XY]
[MSG:INFO: Board 6 Pack]
[MSG:INFO: I2SO BCK:gpio.22 WS:gpio.17 DATA:gpio.21]
[MSG:INFO: SPI SCK:gpio.18 MOSI:gpio.23 MISO:gpio.19]
[MSG:INFO: SD Card cs_pin:gpio.5 detect:NO_PIN]
[MSG:INFO: Stepping:I2S_stream Pulse:4us Dsbl Delay:0us Dir Delay:1us Idle Delay:250ms]
[MSG:INFO: Axis count 3]
[MSG:INFO: Axis X (0.000,1300.000)]
[MSG:INFO:   Motor0]
[MSG:INFO:     stepstick Step:I2SO.2 Dir:I2SO.1 Disable:I2SO.0]
[MSG:INFO:     Neg Limit gpio.16:pu]
[MSG:INFO: Axis Y (0.000,800.000)]
[MSG:INFO:   Motor0]
[MSG:INFO:     stepstick Step:I2SO.5 Dir:I2SO.4 Disable:I2SO.7]
[MSG:INFO:     Neg Limit gpio.26:pu]
[MSG:INFO:   Motor1]
[MSG:INFO:     stepstick Step:I2SO.10 Dir:I2SO.9 Disable:I2SO.8]
[MSG:INFO:     Neg Limit gpio.27:pu]
[MSG:INFO: Axis Z (-5.000,0.000)]
[MSG:INFO:   Motor0]
[MSG:INFO:     rc_servo Pin:gpio.12 Pulse Len(1000,2000)]
[MSG:INFO: Kinematic system: Cartesian]
[MSG:INFO: Using spindle NoSpindle]
[MSG:INFO: Connecting to STA SSID:maison]
[MSG:INFO: Connecting.]
[MSG:INFO: Connecting..]
[MSG:INFO: Connected - IP is 192.168.0.44]
[MSG:INFO: WiFi on]
[MSG:INFO: Start mDNS with hostname:http://fluidnc.local/]
[MSG:INFO: SSDP Started]
[MSG:INFO: HTTP started on port 80]
[MSG:INFO: Telnet started on port 23]

Grbl 3.4 [FluidNC v3.4.5 (wifi) '$' for help]
[MSG:INFO: '$H'|'$X' to unlock]

用户界面软件

WebUI 和 Fluidterm

发生了什么？

我从 v3.4.4 更新到 v3.4.5，没有对硬件或配置文件进行任何其他更改，当我意识到它丢失时，我弹出并重新插入卡。我多次重新启动控制器并关闭所有东西大约一个小时，之后得到相同的结果。

SD 卡一直在正常工作，我希望 SD 卡能够继续工作。

WebUI 报告“无 SD 卡”，这是 Fluidterm 的输出：

--- Available ports:
---  1: /dev/cu.Bluetooth-Incoming-Port 'n/a'
---  2: /dev/cu.SLAB_USBtoUART 'CP2102 USB to UART Bridge Controller'
--- Enter port index or full name: 2
--- Fluidterm on /dev/cu.SLAB_USBtoUART  115200,8,N,1 ---
--- Quit: Ctrl+] or Ctrl+Q | Upload: Ctrl+U | Reset: Ctrl+R ---

ok
$x
[MSG:INFO: Caution: Unlocked]
ok
<Idle|MPos:0.000,0.000,0.000|FS:0,0|WCO:951.000,552.000,0.000>
$sd/list
No SD Card
error:Failed to mount device

--- exit ---

其他信息

没有反应

勒韦里

出现的卡，但不再是 SANDISK 4GB Micro SDHC 存储卡 SDSDQM-004G

米奇布拉德利

这可能与espressif/arduino-esp32#6189有关

米奇布拉德利

这是解决问题的提交。该提交位于 arduinoespressif32 框架的主分支中，但尚未在发布版本中。espressif/arduino-esp32@ bb7df04

勒韦里

该问题已通过 fluidnc-SDFix-test-posix 解决。

米奇布拉德利

好的，我删除了测试版本，我们将继续使用新的框架版本进行适当的发布。

MitchBradley 添加了引用此问题的提交 2022 年 5 月 22 日

Use platform espressif32@^4.3.0

259760a

MitchBradley 提到了这个问题 2022 年 5 月 22 日

使用平台 espressif32@^4.3.0 #443

合并

bdring 关闭此作为完成 50dd6b6 2022 年 5 月 24 日

问题：安装 v3.4.5 后无法挂载 SD 卡#436

评论

控制板